ITN Chapter 2 Quiz Answers Cisco 2019 100%

This quiz covers the content in CCNA R&S Introduction to Networks Chapter 2. It is designed to provide an additional opportunity to practice the skills and knowledge presented in the chapter and to prepare for the Chapter Exam.

You are watching: Why would a technician enter the command copy startup-config running-config?

When a hostname is configured through the Cisco CLI, which three naming conventions are part of the guidelines? (Choose three.)

the hostname should be fewer than 64 characters in lengththe hostname should be written in all lower case charactersthe hostname should contain no spacesthe hostname should end with a special characterthe hostname should begin with a letter
A hostname can be configured with upper or lower case characters and should end with a letter or digit, not a special character. A hostname should start with a letter and no space is allowed for a hostname.

Why would a technician enter the command copy startup-config running-config?

to remove all configurations from the switchto save an active configuration to NVRAMto copy an existing configuration into RAMto make a changed configuration the new startup configuration
Usually, changes are made to a running configuration in RAM and copied to NVRAM. However, in this case, the technician wants to copy a previously saved configuration from NVRAM into RAM in order to make changes to it.?

Which two statements are true regarding the user EXEC mode? (Choose two.)

All router commands are available.Global configuration mode can be accessed by entering the enable command.The device prompt for this mode ends with the “>” symbol.Interfaces and routing protocols can be configured.Only some aspects of the router configuration can be viewed.
User EXEC mode limits access to some show and debug commands. It is the first level of user interface encountered when configuring a router and is intended for investigation of certain functions of the device. The User EXEC prompt is identified with the “>” symbol.

What command will prevent all unencrypted passwords from displaying in plain text in a configuration file?

(config)# enable password secret(config)# enable secret Secret_Password(config-line)# password secret(config)# service password-encryption(config)# enable secret Encrypted_Password
To prevent all configured passwords from appearing in plain text in configuration files, an administrator can execute the service password-encryption command. This command encrypts all configured passwords in the configuration file.

To save time, IOS commands may be partially entered and then completed by typing which key or key combination?

TabCtrl-PCtrl-NUp ArrowRight ArrowDown Arrow

How is SSH different from Telnet?

SSH makes connections over the network, whereas Telnet is for out-of-band access.SSH provides security to remote sessions by encrypting messages and using user authentication. Telnet is considered insecure and sends messages in plaintext.SSH requires the use of the PuTTY terminal emulation program. Tera Term must be used to connect to devices through the use of Telnet.SSH must be configured over an active network connection, whereas Telnet is used to connect to a device from a console connection.
SSH is the preferred protocol for connecting to a device operating system over the network because it is much more secure than Telnet. Both SSH and Telnet are used to connect to devices over the network, and so are both used in-band. PuTTY and Terra Term can be used to make both SSH and Telnet connections.

Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)

VTY interfaceconsole interfaceEthernet interfaceboot IOS modeprivileged EXEC moderouter configuration mode
Access to the VTY and console interfaces can be restricted using passwords. Out-of-band management of the router can be restricted in both user EXEC and privileged EXEC modes.

Which device acts as a gateway to allow hosts to send traffic to remote IP networks?

DNS serverDHCP serverlocal routerlocal switch
For hosts to reach remote networks, they must send traffic to a local router that can route the traffic to the correct destination network. This local router is known as the default gateway and hosts must be configured with this address in order to communicate with devices on remote networks.

An administrator has just changed the IP address of an interface on an IOS device. What else must be done in order to apply those changes to the device?

Copy the running configuration to the startup configuration file.Copy the information in the startup configuration file to the running configuration.Reload the device and type yes when prompted to save the configuration.Nothing must be done. Changes to the configuration on an IOS device take effect as soon as the command is typed correctly and the Enter key has been pressed.
Changes to router and switch configurations take effect as soon as the command is entered. For this reason, it is very important that changes to live production devices are always carefully planned before being implemented. If commands are entered that render the device unstable or inaccessible, the device may have to be reloaded, resulting in network downtime.

A technician configures a switch with these commands:

SwitchA(config)# interface vlan 1SwitchA(config-if)# ip address no shutdown

What is the technician configuring?

Telnet accessSVIpassword encryptionphysical switchport access
For a switch to have an IP address, a switch virtual interface must be configured. This allows the switch to be managed remotely over the network.

An IT technician has manually configured an IP address on a laptop for a new employee. Each time the employee tries to connect to the LAN, the employee receives a duplicate IP address error message. What can the company do to prevent this situation from arising again?

Configure the IP address on an SVI on the laptop.Use a virtual private network instead of the company LAN.Use DHCP to automatically assign addresses.Use laptops that do not require IP addresses.
Assigning IP addresses automatically using DHCP will greatly eliminate the chance of a duplicate IP address error.

Which two functions are provided to users by the context-sensitive help feature of the Cisco IOS CLI? (Choose two.)

providing an error message when a wrong command is submitteddisplaying a list of all available commands within the current modeallowing the user to complete the remainder of an abbreviated command with the TAB keydetermining which option, keyword, or argument is available for the entered commandselecting the best command to accomplish a task
Context-sensitive help provides the user with a list of commands and the arguments associated with those commands within the current mode of a networking device. A syntax checker provides error checks on submitted commands and the TAB key can be used for command completion if a partial command is entered.

Fill in the blank.

In order to test end-to-end connectivity, you would use the ping command.

Noted: There are 4 answers. You can use one of the following: ping, trace, traceroute, and tracert, but in our system you can use only ping.

True or False?

Mobile devices do not require IP addresses to communicate on the Internet.




Fill in the blank.

The component of the operating software that provides the user interface is called the shell .

See more: When A Door Closes A Window Opens, 28 When One Door Closes Another Will Opens Ideas

Operating systems function with a shell, a kernel, and the hardware. The shell interfaces with the users, allowing them to request specific tasks from the device. The kernel provisions resources from the hardware to meet software requirements. The hardware functions by using drivers and their underlying electronics. The hardware represents the physical components of the device.

System Test Exam Answers

Modules 1 – 3 Exam Answers

Modules 4 – 7 Exam Answers

Modules 8 – 10 Exam Answers

Modules 11 – 13 Exam Answers

Modules 14 – 15 Exam Answers

Modules 16 – 17 Exam Answers

Practice Final – ITN Answers

Course Feedback

ITN Practice PT Skills Assessment (PTSA)

Final Exam Answers

Modules 1 – 4 Exam Answers

Modules 5 – 6 Exam Answers

Modules 7 – 9 Exam Answers

Modules 10 – 13 Exam Answers

Modules 14 – 16 Exam Answers

ITN Practice Skills Assessment – PT Answers

SRWE Practice Skills Assessment – PT Part 1 Answers

SRWE Practice Skills Assessment – PT Part 2 Answers

SRWE Hands On Skills Exam Answers

SRWE Practice Final Exam Answers

SRWE Final Exam Answers 

Modules 1 – 2 Exam Answers

Modules 3 – 5 Exam Answers

Modules 6 – 8 Exam Answers

Modules 9 – 12 Exam Answers

Modules 13 – 14 Exam Answers

ITN Practice PT Skills Assessment (PTSA) Answers

SRWE Practice PT Skills Assessment (PTSA) – Part 1 Answers

SRWE Practice PT Skills Assessment (PTSA) – Part 2 Answers

ENSA Practice PT Skills Assessment (PTSA) Answers

ENSA Hands On Skills Exam Answers

Practice Final – ENSA Answers

ENSA Final Exam Answers

CCNA Certification Practice Exam Answers

We are providing training service as the following:



Cloud security








Email security





Domain Register

Load balancer

Free Software

Free Training

Remove malware

Online Degree

Internet Service

Fiber Optic


Cooling System

Security Alarm

Data Center

Core Banking

Network Monitoring Tools



Security Training

Pentest Training

Offensive Security

Window 10

Window Server